The Elevator Editor is an interface into the
inner workings of Skyscraper's elevator system, and is very
elaborate.
Use this window to modify and operate the simulator's elevators
directly.
On the top left, the Number bar selects the elevator number.
Right below it is the Floor bar, which selects the floor (and
shows the ID of the floor also).
Control Section:
Call: call elevator to current floor
Go: go directly to specified floor
Open: open elevator doors
Close: close elevator doors
Open Manual: manually open elevator doors
Close Manual: manually close elevator doors
Enqueue Up: queues the selected floor on the specified
elevator in the Up direction
Enqueue Down: queues the selected floor on the specified
elevator in the Down direction
Select Current Elevator selects the elevator the user is
currently riding in.
Chime plays the chime sound at the currently selected
floor.
Modes:
ACP Mode: anti-crime prevention, causes the elevator to
stop at a specified floor before continuing
Up/Down Peak: sends elevators to the bottom or top of the
assigned floors, to prioritize peak times
Independent service: enables or disables independent
service
Inspection service: enables or disables inspection service
Fire Phase 1 can either be Off, On, or Bypass
Fire Phase 2 can either be Off, On or Hold.
The
Visible checkbox determines if the elevator should be
visible. The
Run checkbox turns on and off the
elevator.
Manual specifies the direction of manual movement, mostly
for Inspection Service mode. To operate inspection mode,
first enable it, and then click Go, and either Up or Down.
General Parameters:
Number is the elevator number.
Name is the elevator name.
ID is the elevator ID, mostly used for Destination Dispatch
Type is the type of elevator, such as Local or Express
Enabled shows if the elevator is enabled or not
Shaft is the assigned shaft of the elevator
Height is the calculated height of the elevator car
DoorSize is deprecated, but is the calculated size of the car
doors
DDirection is the direction the car doors face, and is deprecated
DoorsOpen shows if the car doors are open or not.
Brakes shows if the elevator's brakes are enabled or not.
EmergStop shows the internal status of Emergency Stop
DoorTimer is the door close timer, in the example, is set to 5
seconds
QuickClose is the timer used in quick-close mode, and in the
example is set to 3 seconds
FlrSkipTxt: Floor skip text, shown on the elevator indicator when
skipping floors, used for things such as express levels.
WaitDoors:
Nudge: shows or changes the status of nudge mode
Sensor: enables or disables the door sensor
ActCallFloor is the Active Call Floor
ActCallDir is the Active Call Direction
Notified shows if floor arrival notifications have been performed
WaitTimer:
ChimeDir is the direction the elevator last chimed
LevSpeed is the leveling speed of the elevator
LevOffset is the leveling offset
LevOpen determines the distance from the floor the elevator doors
open when leveling
FlrSounds: enable or disable floor arrival sounds
FlrBeeps: enable or disable floor beeps
MsgSounds: enable or disable message sounds
AutoEnable:
ReOpen:
AutoDoors: if true, doors are automatic, set to false for manual
elevators
OpenStart: if true, open elevator doors on start
Interlocks: enables or disables interlocks
Fan: enables or disables the car fan
Alarm on: if true, the alarm is sounding
MusicOn: play elevator music
MusicMove:
MAlwaysOn: MusicAlwaysOn
ChimeArrival:
The Serviced Floors section allows you to change the serviced
floor list of the elevator.
Position Parameters
Floor: the floor the elevator car is n
Pos: the elevator's position in 3D space
StartFlr:
EStart:
DOrigin: not used anymore, door origin
SDOrigin, not used, shaft door origin
OnFloor: true if elevator is on a floor
Motor: position of motor at top of shaft
Camera:
Music: position of elevator music sound emitter
Queues Parameters
Direction:
LastUp:
LastDwn:
Last:
Resets:
Limit:
Reset - resets both up and down queues
Motion Parameters
UpSpeed:
DownSpeed:
Accel:
Decel:
AccelJerk:
DecelJerk:
Rate:
Direction:
ActiveDir:
JerkRate:
DStopped:
IsIdle:
Manual:
Leveling:
Parking:
ManualMove:
SlowSpd:
ManualSpd:
InsSpeed:
Destination Parameters
Floor: destination floor
IsMoving: true if elevator is moving
Move:
Distance: distance in feet to destination floor
Dest: altitude of destination floor
StopDist: stopping distance in feet
TmpDecel: internal temporary deceleration value
Error:
NotifyEarly: status of the NotifyEarly feature
NotifyLate: status of the NotifyLate feature
DDelay:
ADelay:
Modes Parameters
ACP Floor: the floor used for Anti-Crime Prevention (ACP) mode
Recall Flr: recall floor
Rcl Flr Alt: alternate recall floor
Park Flr: parking floor
Park Dly: number of seconds to wait before parking elevator, if
idle
NudgeTmr: time in seconds to wait before enabling nudge mode